The Bosch Rexroth CDH2 MF4 is a robust, single-rod mill-type hydraulic cylinder designed for demanding applications. It adheres to standards ISO 6022 and DIN 24333 and operates at a nominal pressure of 250 bar .The "MF4" in its designation specifies a round flange mounting at the cylinder base . This mounting style is one of six standard options available for the CDH2 series .📊 Key Specifications for CDH2 MF4 (40mm Bore, 60mm Stroke)Parameter Specification Source(s)Piston Diameter (ØAL) 40 mm Stroke Length (S) 60 mm (Maximum up to 6,000 mm) Piston Rod Diameter (ØMM) 25 mm or 28 mm Piston Rod Thread (KK) M20 x 1.5 Port Thread (EE) G1/2 ⚙️ Weight CalculationThe cylinder's weight depends on the selected piston rod diameter. The base weight (0 mm stroke) is 9 kg . Each 100 mm of stroke adds approximately 0.9 kg (for a 25mm rod) or 1.0 kg (for a 28mm rod) .Calculated Approximate Weight (for 60 mm stroke):With a 25 mm piston rod: 9 kg + (0.6 × 0.9 kg) = 9.54 kg.With a 28 mm piston rod: 9 kg + (0.6 × 1.0 kg) = 9.60 kg.

The Rexroth CDH2 MT4 is a heavy-duty, single-rod mill-type cylinder designed for a nominal pressure of 250 bar (25 MPa) and conforms to ISO 6022 and DIN 24333 standards .The MT4 designation specifies a trunnion (pivot) mount, which allows the cylinder to rotate around a fixed axis. For your specified 40 mm bore and 60 mm stroke, the key specifications are detailed below.📊 Key Specifications for CDH2 MT4 (40mm Bore, 60mm Stroke)This information is sourced from the official Rexroth technical data sheet for the CDH2 series .Parameter SpecificationPiston Diameter (ØAL) 40 mmStroke Length (S) 60 mm (maximum stroke up to 6000 mm)Piston Rod Diameter (ØMM) 25 mm or 28 mm (standard options) Piston Rod Thread (KK) M20 x 1.5 Port Thread (EE) G1/2 Trunnion Diameter (ØTD f8) 25 mm Trunnion Length (TL) 20 mm ⚙️ Weight Calculation for Your CylinderThe weight depends on the chosen piston rod diameter. The base weight and additional weight per stroke increment are as follows :Base Weight (0 mm stroke): 9 kgAdditional Weight per 100 mm Stroke: 0.9 kg (for a 25 mm rod) or 1.0 kg (for a 28 mm rod).Calculated Approximate Weight (for 60 mm stroke):With a 25 mm piston rod: 9 kg + (0.6 × 0.9 kg) = 9.54 kg.With a 28 mm piston rod: 9 kg + (0.6 × 1.0 kg) = 9.60 kg.🔧 Important Trunnion Mounting ConsiderationsBearing Blocks: The MT4 mounting style typically requires a pair of CLTB (trunnion bearing block) accessories for installation . For a 40 mm bore cylinder, the correct bearing block is the CLTB 25 .Dimension Specification: A critical dimension for trunnion mount cylinders is the XV dimension, which positions the trunnion along the cylinder body. This dimension must be specified by the customer .

Single Rod Cylinder(CD) - Mill Type Cylinder (BOSCH , Rexroth) Range H2 to ISO 6022 , DIN 24333. - CDH2 MS2.

The Bosch Rexroth CDH2 MS2 is a robust, single-rod mill-type cylinder designed for a nominal pressure of 250 bar . This model uses an MS2 foot mounting for fixed, rigid installation .Here are the specifications for your 40 mm bore and 60 mm stroke.📊 Key Specifications for CDH2 MS2 (40mm Bore, 60mm Stroke)Parameter SpecificationPiston Diameter (ØAL) 40 mm Stroke Length (S) 60 mm (max 6000 mm possible) Piston Rod Diameter (ØMM) 25 mm or 28 mm (standard options) Piston Rod Thread (KK) M20 x 1.5 Port Thread (EE) G1/2 ⚙️ Weight CalculationThe cylinder's weight depends on the selected piston rod diameter:Base Weight (0 mm stroke): 9 kg .Additional Weight per 100 mm Stroke: 0.9 kg for 25mm rod; 1.0 kg for 28mm rod .Calculated Approximate Weight (for 60 mm stroke):25 mm rod: 9 kg + (0.6 × 0.9 kg) = 9.54 kg.28 mm rod: 9 kg + (0.6 × 1.0 kg) = 9.60 kg.

Based on the official Rexroth technical documentation, the correct clampable swivel head for your CDH1 cylinder with a 40 mm piston diameter is the CGAK 16.This component is designed to attach to the piston rod and compensate for angular misalignment in your hydraulic system.📊 CGAK 16 SpecificationsHere is a summary of its key specifications from the Rexroth catalog data :Parameter SpecificationType CGAK 16For Cylinder (Piston Ø) CDH1/CGH1/CSH1: 40 mmMaterial No. (Maintenance-required) R900303162Material No. (Maintenance-free) R900321784Material No. (Flat Grease Nipple) R900321521Thread (KK) M16 x 1.5Pin Diameter (ØCN) 25 mmLength L1 80 mmClamping Screw ISO 4762 - M8Tightening Torque (MA) 30 NmWeight (m) 0.43 kgStatic Load Rating (C₀) 72 kNMax. Admissible Load (Fadm) 25.9 kNAngle of Misalignment (Z) 7°Installation Note: The self-aligning clevis must always be screwed against the piston rod thread stop. Afterwards, the clamping screws must be tightened with the specified tightening torque .

Rexroth - Bosch Accessories - Self-aligning Clevis - CGAK - Size 22.

Based on the official Rexroth documentation, the correct clampable swivel head for your specified cylinder configurations is the CGAK 22. This component is used to attach to the piston rod while allowing for angular misalignment.📊 CGAK 22 SpecificationsParameter Specification for CGAK 22For Cylinder (Piston Ø) CDH1/CGH1/CSH1: 50 mmCDH3/CGH3/CSH3: 40 mm Material No. (Maintenance-required) R900303163 Material No. (Maintenance-free) R900321683 Material No. (Flat Grease Nipple) R900321522 Thread (KK) M22 x 1.5 Pin Diameter (ØCN) 30 mm Length L1 94 mm Clamping Screw ISO 4762 - M8 Tightening Torque (MA) 30 Nm Weight (m) 0.7 kg Static Load Rating (C₀) 106 kN Max. Admissible Load (Fadm) 38.2 kN Angle of Misalignment (Z) 6° Installation Note: The self-aligning clevis must always be screwed against the piston rod thread stop. Afterwards, the clamping screws must be tightened with the specified tightening torque .

Rexroth - Bosch Accessories - Self-aligning Clevis - CGAK - Size 28.

Based on the official Rexroth technical documentation, the correct clampable swivel head (Gelenkkopf) for your specified cylinder configurations is the CGAK 28. The data shows this accessory is paired with both a CDH1 cylinder with a 63 mm piston and a CDH3 cylinder with a 50 mm piston.📊 CGAK 28 SpecificationsThe table below summarizes the key specifications, including material numbers, dimensions, and load ratings, from the Rexroth catalog data.Parameter Specification for CGAK 28For Cylinder (Piston Ø) CDH1/CGH1/CSH1: 63 mmCDH3/CGH3/CSH3: 50 mmMaterial No. (Maintenance-required) R900303164Material No. (Maintenance-free) R900300717Material No. (Flat Grease Nipple) R900321523Thread (KK) M28 x 1.5Pin Diameter (ØCN) 35 mmLength (L1) 112 mmClamping Screw ISO 4762 - M10Tightening Torque (MA) 54 NmAngle of Misalignment (Z) 6°Weight (m) 1.1 kgStatic Load Rating (C₀) 153 kNMax. Admissible Load (Fadm) 55.1 kN

Rexroth - Bosch Accessories - Self-aligning Clevis - CGAK - Size 35.

Based on the official Rexroth documentation, the correct self-aligning clevis (swivel head) for your specified cylinder configurations is the CGAK 35 .📊 CGAK 35 SpecificationsParameter SpecificationFor Cylinder (Piston Ø) CDH1/CGH1/CSH1: 80 mmCDH3/CGH3/CSH3: 63 mm Material No. (Maintenance-required) R900303165 Material No. (Maintenance-free) R900322738 Thread (KK) M35 x 1.5 Pin Diameter (CN) 40 mm Length (L1) 135 mm Weight (m) 2.0 kg Static Load Rating (C₀) 250 kN Max. Admissible Load (Fadm) 90.0 kN Clamping Screw ISO 4762 - M10 Tightening Torque (MA) 59 Nm Angle of Misalignment (Z) 7° Installation Note: The self-aligning clevis must always be screwed against the piston rod thread stop. Afterwards, the clamping screws must be tightened with the specified torque .

Rexroth - Bosch Accessories - Self-aligning Clevis - CGAK - Size 45.

The correct self-aligning clevis for your specified Rexroth cylinder configurations is the CGAK 45. This swivel head is documented as an accessory for the CDH1 and CGH1 series . The data shows it is compatible with a CDH1 cylinder with a 100 mm piston and a CDH3 cylinder with an 80 mm piston.📊 CGAK 45 SpecificationsHere is a summary of its key specifications from the official Rexroth catalog data :Parameter SpecificationFor Cylinder (Piston Ø) CDH1/CGH1/CSH1: 100 mmCDH3/CGH3/CSH3: 80 mmMaterial No. (Maintenance-required) R900303166 Thread (KK) M45x1.5Pin Diameter (CN) 50 mmLength (L1) 168 mmWeight (m) 3.3 kgStatic Load Rating (C₀) 365 kNMax. Admissible Load (Fadm) 131.4 kNInstallation Note: The self-aligning clevis must always be screwed against the piston rod thread stop. Afterwards, the clamping screws must be tightened with the specified torque.

Rexroth - Bosch Accessories - Self-aligning Clevis - CGAK - Size 58.

The correct self-aligning clevis (swivel head) for a CDH1 cylinder with a 125 mm piston or a CDH3 cylinder with a 100 mm piston is the CGAK 58. This clampable swivel head is detailed in the Rexroth technical documentation for mounting elements .📊 CGAK 58 SpecificationsParameter Specification for CGAK 58For Cylinder (Piston Ø) CDH1/CGH1/CSH1: 125 mmCDH3/CGH3/CSH3: 100 mm Material No. (Maintenance-required) R900303167 Material No. (Maintenance-free) R900322020 Material No. (Flat Grease Nipple) R900321520 Thread (KK) M58 x 1.5 Pin Diameter (ØCN) 60 mm Length (L1) 200 mm Clamping Screw ISO 4762 - M16 Tightening Torque (MA) 250 Nm Weight (m) 5.5 kg Static Load Rating (C₀) 400 kN Max. Admissible Load (Fadm) 144.0 kN ⚠️ Installation Note: The self-aligning clevis must always be screwed against the piston rod thread stop. Afterwards, the clamping screws must be tightened with the specified tightening torque .

The correct self-aligning clevis (swivel head) for your specified Rexroth cylinder configurations is the CGAK 65.This swivel head is documented as an accessory for the CDH1 and CGH1 mill-type cylinder series, which also applies to the CDH3 series under the same technical documentation . The data confirms it is compatible with a CDH1 cylinder with a 140 mm piston and a CDH3 cylinder with a 125 mm piston .📊 CGAK 65 SpecificationsHere is a summary of its key specifications, including the material number, based on the Rexroth technical catalog for the CDH1/CGH1/CSH1 and CDH3/CGH3/CSH3 series :Parameter Specification for CGAK 65For Cylinder (Piston Ø) CDH1/CGH1/CSH1: 140 mmCDH3/CGH3/CSH3: 125 mmMaterial No. (Maintenance-required) R900303168Thread (KK) M65 x 1.5Pin Diameter (CN) 70 mmWeight (approx.) 10.5 kgStatic Load Rating (C₀) 745 kNMax. Admissible Load (Fadm) 268.2 kNAngle of Misalignment (Z) 6°Installation Note: The self-aligning clevis must always be screwed against the shoulder of the piston rod. Afterwards, the clamping screws must be tightened with the specified tightening torque .