The Bosch Rexroth Type FES 40 valve is the correct 2-way proportional throttle valve for your specified configuration without integral control electronics.🔧 Technical Specifications for NG40 FES ValveThe following table summarizes the key technical parameters for the Type FES 40:Parameter SpecificationValve Type FES (2-way proportional throttle valve without integral electronics)Nominal Size (NG) 40Component Series 3X (Series 30-39, dimensions unchanged)Max. Operating Pressure 315 bar (at ports A, B, and X)Porting Pattern DIN ISO 7368 (cartridge type)Nominal Flow Rate 670 L/min (at Δp = 10 bar)Max Flow Rate (A→B) 680 L/min (at Δp = 10 bar)Max Flow Rate (B→A) 585 L/min (at Δp = 10 bar)Area Ratio (Main Spool) 2 : 1Weight 8.2 kg (FES) / 8.4 kg (FESE)💡 Understanding the Valve TypeThe Type FES is designed for use with an external control electronics unit, which must be ordered separately. This is distinct from the "FESE" variant, which has on-board electronics (OBE).Key features of the FES valve include:Pilot-operated, 2-way proportional throttle valve for block installationCommand value-dependent position control of the orifice spoolThe position of the main spool is controlled in a closed loop using an external amplifier and an inductive position transducerIn the event of a power failure, cable break, or withdrawal of the enable signal, the spool automatically moves to the seated position, blocking flow in both directions🔧 Ordering Code ExampleBased on the ordering code structure from the official Rexroth documentation, a complete ordering code for this configuration could be structured as: FES 40 CA-3X/670LK4M.The code elements represent the valve type, size, spool variant, component series, flow rating, and options.Proportional Flow Control Valve (Rexroth - BOSCH).- 2-Way Proportional Throttle Valve Type FES.- Nominal Size 50.- Porting Pattern To DIN 24342 Form A.- Without Integral Control

The Bosch Rexroth valve that matches your exact specification is the Type FES (without integral electronics). For a Type FES valve, external control electronics must be ordered separately . This is distinct from the "FESE" variant, which has on-board electronics (OBE) .🔧 Key Specifications for NG63 FES ValveThe following technical parameters are confirmed for the Nominal Size 63 model from official Rexroth documentation :Parameter Specification for NG63Valve Type FES (2-way proportional throttle valve without integral electronics) Nominal Size (NG) 63 Component Series 3X (Series 30-39, dimensions unchanged) Maximum Operating Pressure 315 bar Porting Pattern DIN ISO 7368 (cartridge type, also known as DIN 24342 Form A) Nominal Flow Rate 1800 L/min (at Δp = 10 bar) Area Ratio (Main Spool) 1.6 : 1 Flow Direction Bidirectional (A→B and B→A) 💡 Understanding the Valve TypeThe Type FES is a pilot-operated 2-way proportional throttle valve designed for block installation, providing continuous flow control . The main spool position is controlled in a closed loop using an external amplifier and an inductive position transducer that provides actual position feedback .Key functional features include:Command value-dependent position control of the orifice spool In the event of a power failure, cable break, or withdrawal of the enable signal, the spool automatically moves to the seated position, blocking flow in both directions Can be used in conjunction with a pressure compensator for pressure-compensated flow control 🔧 Ordering Code ExampleBased on the ordering code structure from the official documentation, a complete ordering code for this configuration is structured as FES 63 CA-3X/1800LK4M (material no. R900979361) . The code elements represent the valve type, size, spool variant, component series, flow rating, and options.

Self-aligning Clevis - Rexroth - Bosch Accessories - CGKL. - Size 10.

Based on the available documentation, the self-aligning clevis matching your specified parameters is the CGKL 10. This accessory is designed for a 10 mm internal bush diameter and is compatible with the CDL1 cylinder series.✅ CGKL 10 SpecificationsParameter SpecificationDesignation CGKL 10 Internal Bush Diameter (DN) 10 mm For Cylinder Range CDL1 (with 25 mm piston diameter)Material Number 3712500031 Standard ISO 12240-4

Self-aligning Clevis - Rexroth - Bosch Accessories - CGKL. - Size 12.

Based on the search results, the self-aligning clevis for your specified parameters is the CGKL 12. This accessory is designed for a 12 mm internal bush diameter and is compatible with the CDL1 cylinder series.✅ CGKL 12 SpecificationsThe table below lists the key specifications for the CGKL 12, confirmed by the product documentation .Parameter SpecificationDesignation CGKL 12Internal Bush Diameter (DN) 12 mmFor Cylinder Range CDL1 (with 32 mm piston diameter) Material Number 3713200031 Standard ISO 12240-4 Thread Gender Male

Based on the available search results, the exact self-aligning clevis you're looking for is a CGKD 12, not a CGKM. The "CGKM" designation you used does not appear in the standard accessory catalog for the CDM1 cylinder series found in these results .However, I have confirmed the correct part and its specifications for your cylinder configurations.✅ Correct Part Identification: CGKD 12For the CDM1 cylinder series with either of the rod end configurations you specified, the compatible self-aligning clevis is the CGKD 12 .The official Rexroth accessory table confirms this:For Cylinder Range Piston Rod End Piston Rod Diameter (d) Self-aligning Clevis TypeCDM1 G 14 mm CGKD 12 CDM1 H 18 mm (with D=25mm) CGKD 12 📊 Specifications for CGKD 12Here are the detailed specifications for the CGKD 12 self-aligning clevis, as provided in the technical catalog :Parameter SpecificationType CGKD 12Material Number R900540998Internal Bush Diameter (DN/CN H7) 12 mmNominal Force 8,000 NThread (KK) M12 x 1.25Clamping Screw M5 x 16 (ISO 4762-10.9)Tightening Torque (Mₜ) 6 NmWeight (m) 0.1 kgMisalignment Angle (Z) 2°📌 Installation Note: The self-aligning clevis must always be screwed to the piston rod thread stop. Subsequently, the clamping screws have to be tightened to the specified torque .

Based on the available Bosch Rexroth technical documentation, the specific CGKM designation you used was not found. However, the search results confirm that the correct self-aligning clevis for your specified configurations is the CGKD 16.✅ Correct Part Identification: CGKD 16For the CDM1 cylinder series with either of the rod end configurations you specified, the compatible self-aligning clevis is the CGKD 16.For Cylinder Range Piston Rod End Piston Rod Diameter (d) Self-aligning Clevis TypeCDM1 G 18 mm CGKD 16CDM1 H 22 mm (with D=32mm) CGKD 16📊 Specifications for CGKD 16Here are the detailed specifications for the CGKD 16 self-aligning clevis, as provided in the technical catalog:Parameter SpecificationType CGKD 16Material Number R900308559Internal Bush Diameter (CN H7) 16 mmNominal Force 12,500 NThread (KK) M14 x 1.5Clamping Screw M6 x 14 (ISO 4762-10.9)Tightening Torque (Mₜ) 10 NmWeight (m) 0.2 kgMisalignment Angle (Z) 2°📌 Installation Note: As noted in the documentation, the self-aligning clevis must always be screwed to the piston rod thread stop. Subsequently, the clamping screws have to be tightened to the specified torque.

Based on the official Rexroth technical documentation, the CGKM designation you used was not found. However, the search results confirm that the correct self-aligning clevis for your specified configuration is the CGKD 20 .✅ Correct Part Identification: CGKD 20For the CDM1 and CDL1 cylinder series, the compatible self-aligning clevis with a 20 mm internal bush diameter (DN) is the CGKD 20 .📊 Specifications for CGKD 20Here are the detailed specifications for the CGKD 20 self-aligning clevis, as provided in the technical catalog :Parameter SpecificationType CGKD 20Material Number R900308576Internal Bush Diameter (CN H7) 20 mmNominal Force 20,000 NThread (KK) M16 x 1.5Clamping Screw M8 x 20 (ISO 4762-10.9)Tightening Torque (Mₜ) 25 NmWeight (m) 0.35 kgMisalignment Angle (Z) 2°📌 Installation Note: As noted in the documentation, the self-aligning clevis must always be screwed to the piston rod thread stop. Subsequently, the clamping screws have to be tightened to the specified torque .

Based on the available Bosch Rexroth technical documentation, a self-aligning clevis with the specific model code CGKM matching your requested size and internal bush diameter (DN=25) was not found. The designation CGKD is the standard type used for clampable swivel heads across the relevant cylinder families.✅ Correct Part Identification: CGKD 25The search results confirm that the correct self-aligning clevis for a 25 mm internal bush diameter (DN/CN H7) is the CGKD 25 for the CDM1 and CDL1 cylinder ranges.This is verified in the official dimension tables for the CDM1 / CGM1 / CSM1 series, where the CGKD 25 is listed with an internal bush diameter (CN H7) of 25 mm . The same model and dimensions are also listed for the CDH2 / CGH2 series , confirming it as a standard component.📊 Specifications for CGKD 25Here are the key specifications for the CGKD 25 self-aligning clevis:Parameter SpecificationType CGKD 25Material Number R900323332 Internal Bush Diameter (CN H7) 25 mm Nominal Force 32,000 N Thread (KK) M20 x 1.5 Clamping Screw M8 x 20 (ISO 4762-10.9) Tightening Torque (Mₐ) 25 - 30 Nm Weight (m) 0.65 kg Misalignment Angle (Z) 2° 📌 Installation Note: As noted in the documentation, the self-aligning clevis must always be screwed to the piston rod thread stop. Subsequently, the clamping screws have to be tightened to the specified torque .

The specific CGKM designation does not appear in the available documentation. The correct self-aligning clevis for a 32 mm internal bush diameter (DN/CN H7) for the CDM1 and CDL1 cylinder ranges is the CGKD 32.✅ Correct Part Identification: CGKD 32This is confirmed by the official dimension tables for both the CDM1 / CGM1 / CSM1 and CDH2 / CGH2 series, where the CGKD 32 is listed with an internal bush diameter of 32 mm.📊 Specifications for CGKD 32Here are the key specifications for the CGKD 32 self-aligning clevis:Parameter SpecificationType CGKD 32Material Number R900322049Internal Bush Diameter (CN H7) 32 mmNominal Force 50,000 NThread (KK) M27 x 2Clamping Screw M10 x 25 (ISO 4762-10.9)Tightening Torque (Mₜ) 49 NmWeight (m) 1.15 kgMisalignment Angle (Z) 4°📌 Installation Note: As noted in the documentation, the self-aligning clevis must always be screwed to the piston rod thread stop. Subsequently, the clamping screws have to be tightened to the specified torque.

Based on the available Bosch Rexroth technical documentation, the CGKM designation you used was not found. However, the search results confirm that the correct self-aligning clevis for a 40 mm internal bush diameter (DN/CN H7) for the CDM1 and CDL1 cylinder ranges is the CGKD 40.✅ Correct Part Identification: CGKD 40This is confirmed by the official dimension tables for both the CDM1 / CGM1 / CSM1 and CDH2 / CGH2 series, where the CGKD 40 is listed with an internal bush diameter (CN H7) of 40 mm.📊 Specifications for CGKD 40Here are the key specifications for the CGKD 40 self-aligning clevis:Parameter SpecificationType CGKD 40Material Number R900322029Internal Bush Diameter (CN H7) 40 mmNominal Force 80,000 NThread (KK) M33 x 2Clamping Screw M10 x 30 (ISO 4762-10.9)Tightening Torque (Mₜ) 49 NmWeight (m) 2.1 kgMisalignment Angle (Z) 4°📌 Installation Note: As noted in the documentation, the self-aligning clevis must always be screwed to the piston rod thread stop. Subsequently, the clamping screws have to be tightened to the specified torque.