Rexroth - Bosch Accessories - pin set CAL32 Pin Set.

The specific "CAL32 Pin Set" was not found in the available search results. The official Rexroth documentation names the key accessory for your cylinder as the self-aligning clevis CGKD .Based on the compatibility table for the CDL1 series, this is the recommended part for your cylinder with a 32mm pin diameter :Rexroth Designation: CGKD 32Rexroth Material No.: R900322049For Cylinder (Piston Ø): 50 mm (or 63 mm, depending on rod) For Piston Rod Thread: M27 x 2 Pin Diameter (EK): 32 mm Nominal Force: 50,000 N ⚠️ Note on Compatibility: The table shows that for a 63mm piston, the matching accessory is actually the CGKD 40 (with a 40mm pin) . The CGKD 32 is typically paired with a 50mm piston . To be sure you have the correct part, please verify the piston rod diameter of your CDL1 cylinder before ordering.

Rexroth - Bosch Accessories - pin set CAL40 Pin Set.

The specific "CAL40 Pin Set" you are looking for does not appear to be listed under that exact name. However, the official Bosch Rexroth documentation confirms the correct matching accessory for your CDL1 cylinder with an 80mm piston is the self-aligning clevis, which includes the required pin.✅ Recommended Accessory: Swivel Head CGKD 40For a CDL1 mill-type cylinder with a piston diameter of 80mm and requiring a 40mm pin diameter, the recommended component is the CGKD 40 self-aligning clevis (swivel head).Parameter SpecificationAccessory Type Self-aligning Clevis / Swivel HeadRexroth Designation CGKD 40Rexroth Material No. R900322029For Cylinder (Piston Ø) 80 mmPin Diameter (EK) 40 mmNominal Force 80,000 NCompatible Piston Rod Thread M33 x 2⚠️ Important Installation Note: The swivel head must always be screwed against the shoulder of the piston rod. Afterwards, the clamping screws must be tightened with the specified tightening torque.

Rexroth - Bosch Accessories - pin set CAL70 Pin Set.

The specific "CAL70 Pin Set" you are looking for does not appear to be a standard, standalone part number. However, the correct matching accessory for a Rexroth CDL1 cylinder with a 160 mm piston diameter and requiring a 70 mm pin is the self-aligning clevis (swivel head) CGKD 70 .This accessory includes the required pin and is the recommended component for your cylinder series and piston size.✅ Recommended Accessory: Self-aligning Clevis CGKD 70Parameter SpecificationAccessory Type Self-aligning Clevis / Swivel Head Rexroth Designation CGKD 70 For Cylinder (Piston Ø) 160 mm Pin Diameter (EK) 70 mm Compatible Piston Rod Thread (KK) M65 x 1.5

Rexroth - Bosch Accessories - pin set CAL80 Pin Set.

The specific "CAL80 Pin Set" is a standard accessory for the Bosch Rexroth CDL1 series. Its part number is 3711600131, and it has a pin diameter of 80 mm.It is compatible with the CDL1 cylinder series. However, based on the official documentation, while the pin set is designed for a cylinder with a 200 mm piston diameter, it is specifically used with the MT4 (trunnion) mounting style for that size cylinder.Here is the specific product information:Parameter SpecificationAccessory Designation CAL80Rexroth Material No. 3711600131Pin Diameter 80 mmFor Cylinder (Piston Ø) 200 mmCompatible Mounting Styles MT4 (for 200mm piston)Weight (approx.) 10.2 kg (per pair)Note on Compatibility: The documentation confirms this pin set is used for both the MP5 and MT4 mounting types generally. However, the specific note for the 200mm piston cylinder indicates its use is limited to the MT4 (trunnion) style.

The specific "CAM12 Pin Set" you are looking for is not documented as a standalone item in the available Rexroth literature. However, based on the official documentation for the CDM1 cylinder series and the "CAM" designation, this likely refers to the mounting pin set for a specific mounting block.I can confirm the compatibility details for a CDM1 cylinder with a 12 mm pin diameter, which depends on the piston rod end type you specified.📋 Compatibility for CAM12 Pin SetFor a CDM1 cylinder with a 12 mm pin diameter, the documentation confirms the following compatibility with your specified piston rod ends:Piston Rod Diameter 14 mm: The standard piston rod thread for a 14 mm rod is M10 x 1.25, as documented for the CDM1 series . This is compatible with the specified "G" piston rod end .Piston Rod Diameter 18 mm: The standard piston rod thread for an 18 mm rod is M14 x 1.5, as documented for the CDM1 series . This is compatible with the specified "H" piston rod end (VW standard thread) .The table below summarizes the key data:Parameter SpecificationAccessory Type Pin Set (Mounting Block Accessory)Rexroth Designation CAM12 (Based on naming convention)Pin Diameter (EK) 12 mmFor Cylinder Series CDM1 (Mill Type Cylinder)For Piston Rod End "G" Piston Rod Ø 14 mm, Thread M10 x 1.25For Piston Rod End "H" Piston Rod Ø 18 mm, Thread M14 x 1.5⚠️ Note on the "CAM" Designation: The "CAM" prefix is not a standard Rexroth code for pins in the documentation I can access. This designation is most likely associated with a specific mounting block (e.g., a CAM clevis bracket) for which this pin set is the required accessory. To confirm the exact part number, you should verify the specific mounting block model you are using.

A specific "CAM16 Pin Set" part number could not be found in the available Bosch Rexroth documentation for the CDM1 cylinder series. However, the technical data confirms the exact piston rod threads and compatibility details you need for this configuration.📋 Configuration Compatibility for CDM1Based on the Rexroth CDM1 series technical data, here are the confirmed specifications for the rod ends you mentioned :Specification Piston Rod End "G" (d=18 mm) Piston Rod End "H" (D=32 mm, d=22 mm)Piston Diameter (ØAL) 32 mm 32 mmPiston Rod Diameter (ØMM) 18 mm 22 mm Rod Thread (KK) M14 x 1.5 (ISO 6020/1) M16 x 1.5 (VW 39 D 920) Swivel Head Compatibility CGKD swivel head, thread type "G" CGKD swivel head, thread type "H" 🔍 Note on "CAM" Designation: The "CAM" prefix is not a standard Rexroth code for mounting pins in the available documentation. The correct term in the catalog for the pin set is simply "Pin" . A "CAM16" pin set would likely be the accessory for a CAM series mounting block used with this cylinder.

Rexroth - Bosch Accessories - pin set CAM20 Pin Set.

No specific "CAM20 Pin Set" part number is available in the search results. However, the Rexroth CDM1 series documentation does confirm the technical data you need to identify the correct accessory.✅ Cylinder Configuration DataBased on the Rexroth CDM1 ordering code and dimensional tables, the thread details for your specified configurations are :Piston Rod End G (d=14 mm): Uses thread M12 x 1.25 (ISO 6020/1) .Piston Rod End H (D=25 mm, d=18 mm): Uses thread M12 x 1.25 (VW 39 D 920) .The correct accessory is likely a pin set for the CAM series mounting block, which the CDM1 technical catalog (RE 17329) lists as a separate accessory item .The exact part number can be found in the official CDM1 / CGM1 / CSM1 catalog, in the "Accessories" section (pages 46 to 54) .

A specific "CAM25 Pin Set" part number could not be found in the available search results. However, based on the Rexroth CDM1 cylinder technical data, here is the key compatibility information for your specified configurations.✅ Piston Rod Thread Data for Your ConfigurationsThe following table summarizes the technical details for the CDM1 rod ends matching your specifications:Specification Piston Rod End "G" (d=28 mm) Piston Rod End "H" (D=50 mm, d=36 mm)Piston Diameter (ØAL) 50 mm 50 mmPiston Rod Diameter (ØMM) 28 mm 36 mmRod Thread (KK) M20 x 1.5 (ISO 6020/1) M27 x 2 (VW 39 D 920)🔍 How to Find the Exact AccessoryThe CAM designation typically refers to a specific mounting block or clevis bracket for which this pin set would be the required accessory. The official Rexroth CDM1 / CGM1 / CSM1 catalog (RE 17329) provides a dedicated "Accessories" section that lists the exact part numbers for all components, including pins and mounting blocks. Consulting this document directly would confirm the precise part number for the CAM25 pin set.

The product number for the Rexroth - Bosch CAM40 Pin Set could not be found in the available search results. However, key compatibility and technical data for your specified CDM1 cylinder configurations are confirmed in the official documentation.Technical Data for Your CDM1 Cylinder ConfigurationsThe following thread specifications are confirmed for the cylinder rod ends you specified :Specification Piston Rod End "G" (d=45 mm) Piston Rod End "H" (D=80 mm, d=56 mm)Piston Diameter (ØAL) 80 mm 80 mmPiston Rod Diameter (ØMM) 45 mm 56 mmRod Thread (KK) M33 x 2 (ISO 6020-1) M42 x 2 (VW standard)How to Find the Exact "CAM40" Pin SetThe correct pin set is the one that matches the specific mounting block (clevis, fork, or trunnion bearing block) used with your CDM1 cylinder . The exact part number for the pin set can be found in the official Bosch Rexroth CDM1 / CGM1 / CSM1 catalog (RE 17329) in the "Accessories" section (pages 46 to 54), where dimensions and specifications are listed by pin diameter (40mm) and cylinder size .

The search results do not contain the specific part number for a CAM50 Pin Set for the Rexroth CDM1 cylinder series. However, they provide the key technical specifications you need to identify the correct accessory.✅ Confirmed CDM1 Cylinder Configuration DataThe following table summarizes the technical details for your specified cylinder rod ends, based on the official Rexroth CDM1 catalog dimension tables:Specification Piston Rod End "G" (d=56 mm) Piston Rod End "H" (D=100 mm, d=70 mm)Piston Diameter (ØAL) 100 mm 100 mmPiston Rod Diameter (ØMM) 56 mm 70 mmRod Thread (KK) M42 x 2 (ISO 6020/1) M48 x 2 (VW standard VW 39 D 920)This data is directly from the CDM1 series dimension tables, which show the rod end threads for different piston and rod diameters .🧭 How to Find the Exact "CAM50" Pin SetThe CAM designation typically identifies a specific mounting block (clevis or fork bracket) within the CDM1 accessory range . The required pin set is the accessory that matches this specific mounting block .To find the exact part number for your pin set, you should consult the official Bosch Rexroth CDM1 / CGM1 / CSM1 catalog (RE 17329). The dedicated "Accessories" section, found on pages 46 to 54 of the catalog, lists all mounting components, including pins, and pairs them with the correct cylinder sizes and rod ends . The table shows that fork-type mounting blocks and their associated pins are assigned based on the piston rod end type (G or H) .