Pilot-operated, balanced-piston relief cartridges are normally closed pressure regulating valves. When the pressure at the inlet (port 1) reaches the valve setting, the valve starts to open to tank (port 2), throttling flow to regulate the pressure. These valves are accurate, have low pressure rise vs. flow, they are smooth and quiet, and are moderately fast.All 2-port relief cartridges (except pilot reliefs) are physically and functionally interchangeable (same flow path, same cavity for a given frame size).Will accept maximum pressure at port 2; suitable for use in cross port relief circuits. If used in cross port relief circuits, consider spool leakage.Minimum setting is 75 psi (5 bar) for all spring ranges.Not suitable for use in load holding applications due to spool leakage.Back pressure on the tank port (port 2) is directly additive to the valve setting at a 1:1 ratio.The main stage orifice is protected against contamination.Cartridges configured with EPDM seals are for use in systems with phosphate ester fluids. Exposure to petroleum based fluids, greases and lubricants will damage the seals.Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity/cartridge machining variations.

This FLeX Series solenoid-operated, 2-stage, balanced relief cartridge is a pressure regulating valve.The valve is normally in relief mode. In relief mode, the valve is open to tank (port 2), throttling flow to regulate the pressure when the pressure at the inlet (port 1) reaches the valve setting. The setting is adjustable with an adjust screw.Energizing the solenoid blocks pilot flow. The valve blocks the flow path from inlet (port 1) to tank (port 2) similar to a spool-type directional valve.Cartridges configured with EPDM seals are for use in systems with phosphate ester fluids. Exposure to petroleum based fluids, greases and lubricants will damage the seals.Designed and tested to 10-million operational cycles at full-rated pressure.Exceeds new NFPA test standard T2.6.1 R2014 for fatigue and burst pressure ratings.Higher flow rates than competing valves of similar size.All configurations of this valve include zinc-nickel plating as standard for 1000-hour salt fog protection.Coil connector options offer ratings up to IP69K. See individual coil product pages for details.This cartridge utilizes both 740 Series high-power and 747 Series hazardous location coils.Back pressure on the tank port (port 2) is directly additive to the valve setting at a 1:1 ratio.Main stage orifice is protected by a 150-micron stainless steel screen.Will accept maximum pressure at port 2.All configurations of this valve are assembled with a non-removable adjust screw.FLeX Series relief valves are fully compatible with the XMD Expandable Mobile Drivers from Sun.A FULL DATA SHEET is available for this model using the link at the top of the page.A wide variety of coil termination and voltage options are available, with and without surge protection. See the CONFIGURATION section.Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity/cartridge machining vari

This FLeX Series solenoid-operated, 2-stage, balanced relief cartridge is a pressure regulating valve.The valve is normally blocked. De-energized, the valve blocks the flow path from inlet (port 1) to tank (port 2) similar to a spool-type directional valve.Energizing the solenoid activates the relief function. In relief mode, the valve opens to tank (port 2), throttling flow to regulate the pressure when the pressure at the inlet (port 1) reaches the valve setting. The setting is adjustable with an adjust screw.Cartridges configured with EPDM seals are for use in systems with phosphate ester fluids. Exposure to petroleum based fluids, greases and lubricants will damage the seals.Designed and tested to 10-million operational cycles at full-rated pressure.Exceeds new NFPA test standard T2.6.1 R2014 for fatigue and burst pressure ratings.Higher flow rates than competing valves of similar size.All configurations of this valve include zinc-nickel plating as standard for 1000-hour salt fog protection.Coil connector options offer ratings up to IP69K. See individual coil product pages for details.This cartridge utilizes both 740 Series high-power and 747 Series hazardous location coils.Back pressure on the tank port (port 2) is directly additive to the valve setting at a 1:1 ratio.Main stage orifice is protected by a 150-micron stainless steel screen.Will accept maximum pressure at port 2.All configurations of this valve are assembled with a non-removable adjust screw.FLeX Series relief valves are fully compatible with the XMD Expandable Mobile Drivers from Sun.A FULL DATA SHEET is available for this model using the link at the top of the page.A wide variety of coil termination and voltage options are available, with and without surge protection. See the CONFIGURATION section.Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity/cartrid

This FLeX Series solenoid-operated, 2-stage, balanced relief cartridge is a pressure regulating valve.The valve is normally in relief mode. In relief mode, the valve is open to tank (port 2), throttling flow to regulate the pressure when the pressure at the inlet (port 1) reaches the valve setting. The setting is adjustable with an adjust screw.Energizing the solenoid opens the main chamber to tank and the valve becomes vented. The pressure drop from the inlet (port 1) to tank (port 2) is typically 100 psi (see performance curves).Cartridges configured with EPDM seals are for use in systems with phosphate ester fluids. Exposure to petroleum based fluids, greases and lubricants will damage the seals.Designed and tested to 10-million operational cycles at full-rated pressure.Exceeds new NFPA test standard T2.6.1 R2014 for fatigue and burst pressure ratings.Higher flow rates than competing valves of similar size.All configurations of this valve include zinc-nickel plating as standard for 1000-hour salt fog protection.Coil connector options offer ratings up to IP69K. See individual coil product pages for details.This cartridge utilizes both 740 Series high-power and 747 Series hazardous location coils.Back pressure on the tank port (port 2) is directly additive to the valve setting at a 1:1 ratio.Main stage orifice is protected by a 150-micron stainless steel screen.Will accept maximum pressure at port 2.All configurations of this valve are assembled with a non-removable adjust screw.FLeX Series relief valves are fully compatible with the XMD Expandable Mobile Drivers from Sun.A FULL DATA SHEET is available for this model using the link at the top of the page.A wide variety of coil termination and voltage options are available, with and without surge protection. See the CONFIGURATION section.Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque a

This FLeX Series solenoid-operated, 2-stage, balanced relief cartridge is a pressure regulating valve.The valve is normally vented. When vented (de-energized), the pressure drop from the inlet (port 1) to tank (port 2) is typically 100 psi (see performance curves).Energizing the solenoid activates the relief function. In relief mode, the valve opens to tank (port 2), throttling flow to regulate the pressure when the pressure at the inlet (port 1) reaches the valve setting. The setting is adjustable with an adjust screw.Cartridges configured with EPDM seals are for use in systems with phosphate ester fluids. Exposure to petroleum based fluids, greases and lubricants will damage the seals.Designed and tested to 10-million operational cycles at full-rated pressure.Exceeds new NFPA test standard T2.6.1 R2014 for fatigue and burst pressure ratings.Higher flow rates than competing valves of similar size.All configurations of this valve include zinc-nickel plating as standard for 1000-hour salt fog protection.Coil connector options offer ratings up to IP69K. See individual coil product pages for details.This cartridge utilizes both 740 Series high-power and 747 Series hazardous location coils.Back pressure on the tank port (port 2) is directly additive to the valve setting at a 1:1 ratio.Main stage orifice is protected by a 150-micron stainless steel screen.Will accept maximum pressure at port 2.All configurations of this valve are assembled with a non-removable adjust screw.FLeX Series relief valves are fully compatible with the XMD Expandable Mobile Drivers from Sun.A FULL DATA SHEET is available for this model using the link at the top of the page.A wide variety of coil termination and voltage options are available, with and without surge protection. See the CONFIGURATION section.Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity

This 2-port, pilot-operated relief cartridge is an electro-proportionally controlled pressure regulating valve. Increasing current to the coil will proportionally increase the pressure setting. When the pressure at port 1 (inlet) is sufficient to overcome the solenoid force, as determined by the analog input signal, the poppet lifts and allows flow from port 1 to port 2 (outlet).Varying the analog input signal to the proportional solenoid provides a step-less control of pressure.For optimum performance, an amplifier with current sensing and adjustable dither should be used. Dither should be adjustable between 100 - 250 Hz.The W-range of this cartridge is designed to work with the 740 Series high-power coil, while the A-range utilizes the 740 Series low-power coil.All configurations of this valve include zinc-nickel plating as standard for 1000-hour salt fog protection.Coil connector options offer ratings up to IP69K. See individual coil product pages for details.The preferred mounting configuration is horizontal or vertically with the coil down. The valve can be mounted coil up if it is installed below reservoir oil level to prevent air accumulation in the solenoid tube. Do not actuate the valve manually or electrically when the valve is not installed.This valve is fully compatible with the XMD Expandable Mobile Drivers from Sun.Coils can be mounted on the tube in either direction.Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity/cartridge machining variations.

Based on the official Bosch Rexroth technical documentation for the CGH3 series, here are the key specifications and hashtags for your cylinder.🔧 Key Specifications: CGH3-MS2, 180mm Bore, 800mm StrokeThe CGH3 is a robust, mill-type double rod cylinder designed for the most demanding, high-pressure industrial applications . The MS2 mounting style designates a foot mounting at the base of the cylinder, providing a secure and rigid installation for heavy-duty use . According to official datasheets, a 180mm bore cylinder is available in the CGH3 series .Parameter Specification for CGH3-MS2 (180mm Bore)Series CGH3 (Mill-type cylinder, double-acting, double rod), Range H3 Mounting Type MS2 (Foot mounting) Nominal Pressure 350 bar (35 MPa) Static Proof Pressure 525 barPiston Diameter (ØAL) 180 mm Piston Rod Diameter (ØMM) Standard options are available; for a 180 mm bore, the table shows a rod diameter of 125 mm Stroke Length (S) 800 mm (Maximum stroke up to 6,000 mm) Standards DIN ISO 3320, ISO 6022 📐 Key Mounting NotesA critical installation detail for the MS2 mounting style is that only one line connection position is possible . This is an important factor to consider for your hydraulic system layout.🧾 Ordering Code ReferenceThe ordering code for your cylinder follows this structure:CG H3 MS2 / 180 / / 800 A 3X / ...In this code:CG = Double-acting cylinderH3 = Range H3MS2 = Mounting style (foot mounting)180 = Piston diameter in mm = e.g., 125 mm (to be specified)800 = Stroke length in mmA = Design principle (head and base flanged)3X = Component series

Based on the official Bosch Rexroth technical documentation for the CGH2 mill-type cylinder series, here are the specifications and hashtags for your configuration.🔧 Key Specifications: CGH2-MT4, 125mm Bore, 300mm StrokeThe CGH2 is a robust double-acting cylinder designed for high-pressure industrial applications . The "MT4" mounting style designates a trunnion (pivot) mount, allowing the cylinder to follow the arc of a moving mechanism and compensate for angular misalignment .Parameter Specification for CGH2-MT4 (125mm Bore)Series CGH2 (Mill-type cylinder, double-acting, double rod), Range H2 Mounting Type MT4 (Trunnion mount) Nominal Pressure 250 bar (25 MPa) Static Proof Pressure 375 bar Piston Diameter (ØAL) 125 mm Piston Rod Diameter (ØMM) Standard options are 80 mm or 90 mm for this bore size Stroke Length (S) 300 mm (Maximum up to 6000 mm) Standards DIN 24333, ISO 6022 📐 Key Mounting Dimensions for MT4 (125mm Bore)Based on the Rexroth dimension tables , the following critical dimensions apply for a 125 mm bore cylinder with MT4 trunnion mounting:Dimension Value (mm)Port Thread (EE) G 1 Piston Rod Thread (KK) M64 x 3 (for 80mm rod) Y 153 PJ 205 X1 100.5 WA 31 Trunnion Diameter (ØD) 206 🔧 Important Ordering NoteThe trunnion position is freely selectable. When ordering, the "XV" dimension (the trunnion position measured from the cylinder base) must always be specified in the plain text in millimeters .🧾 Ordering Code ReferenceThe ordering code for your cylinder follows this structure :CG H2 MT4 / 125 / / 300 A 3X / ...In this code:CG = Double-acting cylinder H2 = Series MT4 = Mounting style (trunnion mount) 125 = Piston diameter in mm = e.g., 80 or 90 mm 300 = Stroke length in mmA = Design principle (head and base flanged) 3X = Component series (30 to 39, unchanged installation and connection dimensions)

Based on the official Bosch Rexroth technical documentation, here are the details for your CGH1-MF3 mill-type double rod cylinder with a 100 mm bore and 500 mm stroke, along with a set of suggested hashtags.🔧 Key Specifications: CGH1-MF3, 100mm Bore, 500mm StrokeThe CGH1 is a robust, mill-type double rod cylinder designed for high-pressure industrial applications. The "MF3" mounting style designates a round flange at the cylinder head.Parameter Specification for CGH1-MF3 (100mm Bore)Series CGH1 (Mill Type Double Rod Cylinder), Range H1Mounting Type MF3 (Round flange at cylinder head)Nominal Pressure 250 bar (25 MPa)Static Proof Pressure 375 bar (37.5 MPa)Piston Diameter (ØAL) 100 mmPiston Rod Diameter (ØMM) Standard options are 56 mm or 70 mmStroke Length (S) 500 mm (Maximum up to 6000 mm)📐 Key Dimensions for MF3 Mounting (100mm Bore)The following critical dimensions are specified in the Rexroth catalog for a 100mm bore cylinder with MF3 mounting:Dimension Value (mm)Flange Diameter (D) 170Flange Hole Circle (DA) 125Flange Hole Diameter (D4) 47Port Thread (EE) G 1Piston Rod Thread (KK) M45x1.5 (for 56mm rod)Dimension PJ 171🧾 Ordering Code ReferenceThe ordering code for your cylinder follows this structure:CG H1 MF3 / 100 / / 500 A 3X / ...For example, a complete code might look like:CGH1MF3/100/56/500A3X/B11CADMWIn this code:CG = Double rod cylinderH1 = SeriesMF3 = Mounting style (round flange at head)100 = Piston diameter in mm<56> = Piston rod diameter in mm (to be specified)500 = Stroke length in mmA = Design principle (head and base flanged)3X = Component series (unchanged installation dimensions)

Mono Pump HMK40 is a specific model in a family of horizontal, multistage centrifugal pumps .Here is a breakdown of its key features based on the search results:Feature DescriptionProduct Name Mono Pump HMK40Type Horizontal multistage centrifugal pump .Key Components Includes stator, universal joint, shaft, bearings, and pump housing as shown in your diagram.Model Size "40" is one of five standard size variants (32, 40, 50, 65, 80) .Flexibility The number of stages can vary (typically 2 to 14) to meet different pressure requirements .Flange Standard Suction and discharge flanges are designed to be compatible with the PN40 standard .This type of pump is commonly used for applications such as water supply, pressure boosting, and irrigation systems .Since different "HMK40" models can have varying stages and connection types depending on the specific needs of a system, I would need to know exactly what application you have in mind to tell you more about its performance.