The Rexroth CDT3-MT1 with a 160 mm bore and 200 mm stroke is a standard configuration from this tie-rod cylinder series. The "MT1" mounting style refers to a head trunnion mount, which allows the cylinder to pivot around a fixed axis at its front end .Here are the key specifications for your cylinder, along with a set of suggested hashtags for your post.🔧 Key Specifications: CDT3-MT1, 160mm Bore, 200mm StrokeParameter Specification for CDT3-MT1 (160mm Bore)Series CD – Single-rod hydraulic cylinder, T3 Style Mounting Type MT1 – Head trunnion (pivot at the cylinder head) Nominal Pressure 160 bar (16 MPa) Standards ISO 6020-2, DIN 24554 Piston Diameter (ØAL) 160 mmPiston Rod Diameter (ØMM) For a 160 mm bore, standard rod options include 70 mm and 90 mm, but other sizes are also available .Stroke Length (S) 200 mm (Series max is 3,000 mm) ⚙️ Mounting Details and Ordering NotesHead Trunnion Mounting: The MT1 style allows the cylinder to pivot at its front end. This helps to compensate for misalignments in the application and reduce side loads on the piston rod and seals . Periodic greasing of the trunnions is recommended for long service life .Trunnion Position: For the MT1 mounting, the trunnion position is typically at the cylinder head. The position is fixed and you do not need to specify an "XV" dimension in the clear text, unlike with a center trunnion (MT4) mount .Ordering Code Reference: The complete Rexroth ordering code follows this structure. A full example is CDT3MT1/160/70/200Z3X/B11..., where you would specify the rod diameter, cushioning options, seal type, and other required features .

Based on the Bosch Rexroth documentation, here are the details for your CDT3-MP3 tie-rod cylinder configuration with a 160mm bore and 200mm stroke, along with suggested hashtags.🔧 Key Specifications: CDT3-MP3, 160mm Bore, 200mm StrokeThe CDT3 is a single-rod tie-rod hydraulic cylinder with a nominal pressure of 160 bar (16 MPa) and conforms to standards ISO 6020-2 and DIN 24554 . The MP3 mounting style designates a swivel eye (pivot mounting) at the cylinder base .Parameter Specification for CDT3-MP3 (160mm Bore)Series CD (Single-rod hydraulic cylinder), T3 Style Mounting Type MP3 (Swivel eye at cylinder base) Nominal Pressure 160 bar (Maximum 210 bar for static loads) Standards ISO 6020-2, DIN 24554 Piston Diameter (ØAL) 160 mm Piston Rod Diameter (ØMM) Standard options include a range of sizes; for a 160mm bore, typical rods like 70 mm or 90 mm are available Stroke Length (S) 200 mm (Maximum up to 3000 mm) Port Thread G 1 for a 160mm bore ⚙️ Key Mounting and Ordering NotesSwivel Eye Mounting: The MP3 mounting style (swivel eye at the base) allows the cylinder to pivot, compensating for minor angular misalignments and reducing side loading on the piston rod and seals .Line Connection: For piston diameters from 125 to 200 mm with this series, only line connection "B" is possible .Ordering Code Structure: The Rexroth ordering code for your cylinder follows the structure CDT3MP3/160//200Z3X.... You would need to specify the piston rod diameter and additional options like cushioning and seals to complete the order code .

Based on the available technical documentation for the Bosch Rexroth CDT3 series, here is a summary of the specifications for your cylinder configuration, along with suggested hashtags.🔧 Key Specifications: CDT3-MP1, 160mm Bore, 200mm StrokeThe CDT3 is a single-rod tie-rod hydraulic cylinder with a nominal pressure of 160 bar (16 MPa) and conforms to standards ISO 6020-2 and DIN 24554 . The MP1 mounting style designates a fork (clevis) mount at the cylinder base .Parameter Specification for CDT3-MP1 (160mm Bore)Series CD (Single-rod hydraulic cylinder), T3 Style Mounting Type MP1 (Fork / Clevis at cylinder base) Nominal Pressure 160 bar (Maximum 210 bar for static loads) Standards ISO 6020-2, DIN 24554 Piston Diameter (ØAL) 160 mm Piston Rod Diameter (ØMM) For a 160mm bore, standard rod diameter options include 70 mm and 90 mm Stroke Length (S) 200 mm (Maximum up to 3000 mm) ⚙️ About the MP1 MountingThe MP1 mounting style means the cylinder features a fork (clevis) at the base . This type of mounting allows the cylinder to pivot and compensates for minor angular misalignments in your application, which can help reduce side loading on the piston rod and seals.📝 Ordering Code ExampleThe Rexroth ordering code for your cylinder follows this structure. You would need to specify the exact piston rod diameter and other options like cushioning or seals to complete the order code .CDT3MP1/160//200...For example, a possible code might look like: CDT3MP1/160/70/200... .

Based on the available technical documentation for the Bosch Rexroth CDT3 series, here is a summary of your cylinder configuration and its mounting style, along with suggested hashtags.🔧 Key Specifications: CDT3-MT4, 160mm Bore, 200mm StrokeThe CDT3 is a single-rod tie-rod hydraulic cylinder designed for a nominal pressure of 160 bar . The MT4 mounting style designates a center trunnion mount, which allows the cylinder to pivot and follow the arc of a moving mechanism .Parameter Specification for CDT3-MT4 (160mm Bore)Series CD – Single-rod hydraulic cylinder, T3 Style Mounting Type MT4 – Center trunnion mount Nominal Pressure 160 bar (Maximum 210 bar for static loads) Standards ISO 6020-2, DIN 24554 Piston Diameter (ØAL) 160 mm Piston Rod Diameter (ØMM) For a 160mm bore, the table shows a standard rod diameter of 70 mm Stroke Length (S) 200 mm (Maximum stroke up to 3,000 mm) 📐 Key Mounting Dimensions for MT4 (160mm Bore)Based on the Rexroth dimension tables, the following critical dimensions apply for a 160mm bore cylinder with MT4 trunnion mounting :Dimension / Specification Value (mm)Port Thread (EE) G 1/2 Piston Rod Thread (KK) M42x2 (for 70mm rod) Trunnion Diameter (ØTD) 70 XV (Trunnion position from base) 131 + stroke (must be specified when ordering) ZB (Retracted length) 277 🛠️ Installation NotesFor the MT4 mounting style:The trunnion position is freely selectable. When ordering, the "XV" dimension (in mm) must always be specified in the clear text .For a 160mm piston diameter with MT4 mounting, only line connection "B" is possible .🧾 Ordering Code ReferenceThe ordering code for your cylinder follows this structure:textCDT3MT4/160//200...A complete code example for a 160mm bore, 70mm rod would be:CDT3MT4/160/70/200...

Fast-acting, pilot-operated, balanced piston relief cartridges are normally closed, pressure-limiting valves used to protect hydraulics components from pressure transients. Fast opening and closing is gained at the expense of smoothness. When the pressure at the inlet (port 1) reaches the valve setting, the valve starts to open to tank (port 2), throttling flow to limit the pressure rise. These valves have low pressure rise vs. flow and are very fast.All 2-port relief cartridges (except pilot reliefs) are physically and functionally interchangeable (same flow path, same cavity for a given frame size).Will accept maximum pressure at port 2; suitable for use in cross port relief circuits. If used in cross port relief circuits, consider spool leakage.Main stage orifice is protected by a 150-micron stainless steel screen.Not suitable for use in load holding applications due to spool leakage.Back pressure on the tank port (port 2) is directly additive to the valve setting at a 1:1 ratio.Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity/cartridge machining variations.

The bi-directional, direct-acting relief cartridge is a normally closed, pressure-limiting valve used to protect hydraulic components from pressure transients. When the pressure differential between ports 1 and 2 exceeds the valve setting, the valve starts to open, throttling flow to limit the pressure rise, regardless of the direction.Because the modulating occurs inside the cartridge, these valves are immune to most of the problems associated with cavitation, namely manifold erosion.The seals on the adjust screw are exposed to system pressure which means this valve can only be adjusted when the pressure is removed. The setting procedure is; check the setting, remove the pressure, adjust the valve, check the new setting.Valve is relatively insensitive to varying oil temperatures and oil borne contamination.Select a spring range where the desired relief setting is approximately mid-range to high between the minimum and maximum pressure to ensure maximum valve repeatability.A deep socket will be needed to install the valve, if the locating shoulder is recessed into the manifold and a crows foot cannot be used to install it.

Pilot-operated, balanced-piston relief cartridges are normally closed pressure regulating valves. When the pressure at the inlet (port 1) reaches the valve setting, the valve starts to open to tank (port 2), throttling flow to regulate the pressure. These valves are accurate, have low pressure rise vs. flow, they are smooth and quiet, and are moderately fast.All 2-port relief cartridges (except pilot reliefs) are physically and functionally interchangeable (same flow path, same cavity for a given frame size).Will accept maximum pressure at port 2; suitable for use in cross port relief circuits. If used in cross port relief circuits, consider spool leakage.Main stage orifice is protected by a 150-micron stainless steel screen.Not suitable for use in load holding applications due to spool leakage.Back pressure on the tank port (port 2) is directly additive to the valve setting at a 1:1 ratio.Cartridges configured with EPDM seals are for use in systems with phosphate ester fluids. Exposure to petroleum based fluids, greases and lubricants will damage the seals.W and Y controls (where applicable) can be specified with or without a special setting. When no special setting is specified, the valve is adjustable throughout its full range using the W or Y control. When a special setting is specified, this setting represents the maximum setting of the valve.Corrosion resistant cartridge valves are intended for use in corrosive environments and are identified by the model code suffix /AP for external stainless steel components, or /LH for external zinc-nickel plated components. See the CONFIGURATION section for all options. For further details, please see the Materials of Construction page located under TECH RESOURCES.Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity/cartridge machining variations.

Pilot-operated, balanced-piston relief cartridges are normally closed pressure regulating valves. When the pressure at the inlet (port 1) reaches the valve setting, the valve starts to open to tank (port 2), throttling flow to regulate the pressure. These valves are accurate, have low pressure rise vs. flow, they are smooth and quiet, and are moderately fast.All 2-port relief cartridges (except pilot reliefs) are physically and functionally interchangeable (same flow path, same cavity for a given frame size).Will accept maximum pressure at port 2; suitable for use in cross port relief circuits. If used in cross port relief circuits, consider spool leakage.Main stage orifice is protected by a 150-micron stainless steel screen.Not suitable for use in load holding applications due to spool leakage.Back pressure on the tank port (port 2) is directly additive to the valve setting at a 1:1 ratio.Cartridges configured with EPDM seals are for use in systems with phosphate ester fluids. Exposure to petroleum based fluids, greases and lubricants will damage the seals.W and Y controls (where applicable) can be specified with or without a special setting. When no special setting is specified, the valve is adjustable throughout its full range using the W or Y control. When a special setting is specified, this setting represents the maximum setting of the valve.Corrosion resistant cartridge valves are intended for use in corrosive environments and are identified by the model code suffix /AP for external stainless steel components, or /LH for external zinc-nickel plated components. See the CONFIGURATION section for all options. For further details, please see the Materials of Construction page located under TECH RESOURCES.Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity/cartridge machining variations.

This 2-port, pilot-operated relief cartridge is an electro-proportionally controlled, normally-closed pressure regulating valve. The valve is spring biased closed to its highest setting (customer specified). Increasing current to the coil will proportionally decrease the pressure setting. When the pressure at port 1 (inlet) is sufficient to overcome the spring force minus the solenoid force, as determined by the analog input signal, the poppet lifts and allows flow from port 1 to port 2 (outlet).The setting represents the maximum relief pressure which the valve will default to with no command. As the command increases, the relief setting will decrease. See performance curves for selected pressure range.Varying the analog input signal to the proportional solenoid provides a step-less control of pressure.Damped construction provides stable operation over a wide range of operating conditions.For optimum performance, an amplifier with current sensing and adjustable dither should be used. Dither should be adjustable between 100 - 250 Hz.This cartridge utilizes 740 Series low-power and high-power coils, and 747 Series hazardous location coils.All configurations of this valve include zinc-nickel plating as standard for 1000-hour salt fog protection.Coil connector options offer ratings up to IP69K. See individual coil product pages for details.This valve is fully compatible with the XMD Expandable Mobile Drivers from Sun.The preferred mounting configuration is horizontal or vertically with the coil down. The valve can be mounted coil up if it is installed below reservoir oil level to prevent air accumulation in the solenoid tube. Do not actuate the valve manually or electrically when the valve is not installed.Coils can be mounted on the tube in either direction.Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity/cartridge machining variations.

Based on the official Bosch Rexroth technical documentation for the CGH3 mill-type cylinder series, here are the key specifications and hashtags for your CGH3-MT4 configuration .🔧 Key Specifications: CGH3-MT4, 180mm Bore, 800mm StrokeThe CGH3 is a robust, double-acting cylinder designed for the most demanding high-pressure industrial applications, with a nominal pressure of 350 bar . The "MT4" mounting style designates a trunnion (pivot) mount, which allows the cylinder to follow the arc of a moving mechanism and compensate for angular misalignment .Parameter Specification for CGH3-MT4 (180mm Bore)Series CGH3 (Mill-type cylinder, double-acting, double rod), Range H3 Mounting Type MT4 (Trunnion mount) Nominal Pressure 350 bar (35 MPa) Static Proof Pressure 525 bar Piston Diameter (ØAL) 180 mm Piston Rod Diameter (ØMM) The standard rod diameter for a 180mm bore in this series is 125 mm Stroke Length (S) 800 mm (Maximum available stroke length is 3,000 mm for this piston diameter) Standards DIN ISO 3320, ISO 6022 📐 Key Mounting Dimensions for MT4 (180mm Bore)Based on the Rexroth dimension tables, the following critical specifications apply for a 180mm bore cylinder with MT4 trunnion mounting :Dimension / Specification ValuePort Thread (EE) G 1 1/2 Piston Rod Thread (KK) M110x2 Y Dimension 241 mm PJ Dimension 264 mm X1 Dimension 159.5 mm ZB Dimension 565 mm 🧾 Ordering Code ReferenceThe ordering code for your cylinder follows this structure :CG H3 MT4 / 180 / 125 / 800 A 3X / ...In this code:CG = Double-acting cylinder, double rodH3 = Range H3MT4 = Mounting style (trunnion mount)180 = Piston diameter in mm125 = Piston rod diameter in mm800 = Stroke length in mmA = Design principle (head and base flanged)3X = Component series (30 to 39, unchanged installation and connection dimensions)Important Ordering Note: The trunnion position is freely selectable. When ordering, the "XV"