Pilot-operated, balanced-piston relief cartridges are normally closed pressure regulating valves. When the pressure at the inlet (port 1) reaches the valve setting, the valve starts to open to tank (port 2), throttling flow to regulate the pressure. These valves are accurate, have low pressure rise vs. flow, they are smooth and quiet, and are moderately fast.All 2-port relief cartridges (except pilot reliefs) are physically and functionally interchangeable (same flow path, same cavity for a given frame size).Will accept maximum pressure at port 2; suitable for use in cross port relief circuits. If used in cross port relief circuits, consider spool leakage.Main stage orifice is protected by a 150-micron stainless steel screen.Not suitable for use in load holding applications due to spool leakage.Back pressure on the tank port (port 2) is directly additive to the valve setting at a 1:1 ratio.Cartridges configured with EPDM seals are for use in systems with phosphate ester fluids. Exposure to petroleum based fluids, greases and lubricants will damage the seals.W and Y controls (where applicable) can be specified with or without a special setting. When no special setting is specified, the valve is adjustable throughout its full range using the W or Y control. When a special setting is specified, this setting represents the maximum setting of the valve.Corrosion resistant cartridge valves are intended for use in corrosive environments and are identified by the model code suffix /AP for external stainless steel components, or /LH for external zinc-nickel plated components. See the CONFIGURATION section for all options. For further details, please see the Materials of Construction page located under TECH RESOURCES.Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity/cartridge machining variations.

This 2-port, pilot-operated relief cartridge is an electro-proportionally controlled, normally-closed pressure regulating valve. The valve is spring biased closed to its highest setting (customer specified). Increasing current to the coil will proportionally decrease the pressure setting. When the pressure at port 1 (inlet) is sufficient to overcome the spring force minus the solenoid force, as determined by the analog input signal, the poppet lifts and allows flow from port 1 to port 2 (outlet).The setting represents the maximum relief pressure which the valve will default to with no command. As the command increases, the relief setting will decrease. See performance curves for selected pressure range.Varying the analog input signal to the proportional solenoid provides a step-less control of pressure.Damped construction provides stable operation over a wide range of operating conditions.For optimum performance, an amplifier with current sensing and adjustable dither should be used. Dither should be adjustable between 100 - 250 Hz.This cartridge utilizes 740 Series low-power and high-power coils, and 747 Series hazardous location coils.All configurations of this valve include zinc-nickel plating as standard for 1000-hour salt fog protection.Coil connector options offer ratings up to IP69K. See individual coil product pages for details.This valve is fully compatible with the XMD Expandable Mobile Drivers from Sun.The preferred mounting configuration is horizontal or vertically with the coil down. The valve can be mounted coil up if it is installed below reservoir oil level to prevent air accumulation in the solenoid tube. Do not actuate the valve manually or electrically when the valve is not installed.Coils can be mounted on the tube in either direction.Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity/cartridge machining variations.

Based on the official Bosch Rexroth technical documentation for the CGH3 mill-type cylinder series, here are the key specifications and hashtags for your CGH3-MT4 configuration .🔧 Key Specifications: CGH3-MT4, 180mm Bore, 800mm StrokeThe CGH3 is a robust, double-acting cylinder designed for the most demanding high-pressure industrial applications, with a nominal pressure of 350 bar . The "MT4" mounting style designates a trunnion (pivot) mount, which allows the cylinder to follow the arc of a moving mechanism and compensate for angular misalignment .Parameter Specification for CGH3-MT4 (180mm Bore)Series CGH3 (Mill-type cylinder, double-acting, double rod), Range H3 Mounting Type MT4 (Trunnion mount) Nominal Pressure 350 bar (35 MPa) Static Proof Pressure 525 bar Piston Diameter (ØAL) 180 mm Piston Rod Diameter (ØMM) The standard rod diameter for a 180mm bore in this series is 125 mm Stroke Length (S) 800 mm (Maximum available stroke length is 3,000 mm for this piston diameter) Standards DIN ISO 3320, ISO 6022 📐 Key Mounting Dimensions for MT4 (180mm Bore)Based on the Rexroth dimension tables, the following critical specifications apply for a 180mm bore cylinder with MT4 trunnion mounting :Dimension / Specification ValuePort Thread (EE) G 1 1/2 Piston Rod Thread (KK) M110x2 Y Dimension 241 mm PJ Dimension 264 mm X1 Dimension 159.5 mm ZB Dimension 565 mm 🧾 Ordering Code ReferenceThe ordering code for your cylinder follows this structure :CG H3 MT4 / 180 / 125 / 800 A 3X / ...In this code:CG = Double-acting cylinder, double rodH3 = Range H3MT4 = Mounting style (trunnion mount)180 = Piston diameter in mm125 = Piston rod diameter in mm800 = Stroke length in mmA = Design principle (head and base flanged)3X = Component series (30 to 39, unchanged installation and connection dimensions)Important Ordering Note: The trunnion position is freely selectable. When ordering, the "XV"

Based on the official Bosch Rexroth technical documentation, here are the specifications for your CGH2-MS2 mill-type double rod cylinder with a 125 mm bore and 300 mm stroke, along with suggested hashtags.🔧 Key Specifications: CGH2-MS2, 125mm Bore, 300mm StrokeThe CGH2 is a robust, mill-type double rod cylinder designed for high-pressure industrial applications . The "MS2" mounting style designates a foot mounting , which provides a fixed and rigid installation.Parameter Specification for CGH2-MS2 (125mm Bore)Series CGH2 (Mill Type Double Rod Cylinder), Range H2Mounting Type MS2 (Foot mounting) Nominal Pressure 250 bar (25 MPa) Static Proof Pressure 375 bar Piston Diameter (ØAL) 125 mmPiston Rod Diameter (ØMM) Standard options are 80 mm or 90 mm for this bore size Stroke Length (S) 300 mm (Maximum up to 6000 mm) Standards DIN 24333, ISO 6022 📐 Mounting Dimensions (MS2 Foot Mounting)The table below summarizes key mounting dimensions for the MS2 style on a 125mm bore cylinder, based on official Rexroth data :Dimension Value (mm)Port Thread (EE) G 1 Piston Rod Thread (KK) M64 x 3 (for 80mm rod) X1 100.5 WA 31 Y 153 PJ 205 🧾 Ordering Code ReferenceThe ordering code for your cylinder follows this structure :CG H2 MS2 / 125 / / 300 A 3X / ...In this code:CG = Double-acting cylinder H2 = Series MS2 = Mounting style (foot mounting) 125 = Piston diameter in mm = e.g., 80 or 90 mm 300 = Stroke length in mmA = Design principle (head and base flanged) 3X = Component series (30 to 39, unchanged installation and connection dimensions)

Based on the official Bosch Rexroth documentation, here are the details for your CGH1-MS2 mill-type double rod cylinder with a 100 mm bore and 500 mm stroke, along with suggested hashtags.🔧 Key Specifications: CGH1-MS2, 100mm Bore, 500mm StrokeThe CGH1 is a robust, mill-type double rod cylinder designed for high-pressure industrial applications with balanced loads in both directions . The "MS2" mounting style designates a foot mounting, which provides a fixed and rigid installation .Parameter Specification for CGH1-MS2 (100mm Bore)Series CGH1 (Mill Type Double Rod Cylinder), Range H1Mounting Type MS2 (Foot mounting) Nominal Pressure 250 bar (25 MPa) Static Proof Pressure 375 bar (37.5 MPa) Piston Diameter (ØAL) 100 mmPiston Rod Diameter (ØMM) Standard options are 56 mm or 70 mm for this bore size Stroke Length (S) 500 mm (Maximum stroke length is 6000 mm) Max. Stroke Velocity 0.20 m/s (for 100mm piston) 📐 Mounting Dimensions (MS2 Foot Mounting)The table below summarizes key mounting dimensions for the MS2 style on a 100mm bore cylinder, based on official Rexroth data :Dimension Value (mm)X1 The official Rexroth dimension sheets are required to confirm this specific value.WA The official Rexroth dimension sheets are required to confirm this specific value.L The official Rexroth dimension sheets are required to confirm this specific value.Line Connection Note: With the MS2 mounting style, only one line connection position is possible . Please refer to the Rexroth ordering code documentation (RE 17332) for the exact configuration.🧾 Ordering Code ReferenceThe ordering code for your cylinder follows this structure :CG H1 MS2 / 100 / / 500 A 3X / ...In this code:CG = Double rod cylinderH1 = SeriesMS2 = Mounting style (foot mounting)100 = Piston diameter in mm = e.g., 56 or 70 mm 500 = Stroke length in mmA = Design principle (head and base flanged)3

Rexroth - Bosch Plain Clevis (Type CSA 80 , CSA 80 B)

Based on the technical documentation, here are the specifications for the Rexroth Plain Clevis Type CSA 80 and its compatibility details .📊 Specifications for CSA 80Parameter SpecificationType CSA 80Thread (KK) M80 x 2Screw-in Length (LE) 80 mmLength (L1) 265 mmWeight (m) 12.2 kgStatic Load Rating (C₀) 670 kNMax. Admissible Load (F_adm) 241.2 kN🔗 Cylinder CompatibilityThe CSA 80 clevis is designed for use with specific piston diameters (ØAL) across the following Rexroth cylinder series :CDH1; CGH1; CSH1 series: Piston diameter ØAL 160 mmCDH3; CGH3; CSH3 series: Piston diameter ØAL 140 mm📝 Installation NoteThe clevis must always be screwed firmly against the shoulder of the piston rod until tight

Based on the available search results, I can provide the general specifications for the Rexroth CD70H series, which includes your specified cylinder size. The specific technical datasheet for this exact configuration appears to be unavailable.📊 Confirmed Technical SpecificationsThe Rexroth CD70 series (which includes the CD70H model) has the following confirmed specifications for the 25mm piston diameter:Parameter SpecificationSeries CD70 (Tie-Rod Cylinder) Nominal Pressure 70 bar <7> Piston Diameter (ØAL) 25 mm (range: 25…200 mm) Piston Rod Diameter (ØMM) 12 mm (range: 12…140 mm) Stroke Length Up to 3,000 mm (your specified 200 mm is well within this range) 🔍 Product IdentificationThe CD70H designates a hydraulic cylinder from this series, and its existence is confirmed by examples like the CD70H 25/16 model (where 25 is the piston diameter and 16 is the piston rod diameter) . Other similar models, such as CD70H32/18, confirm the "H" designation is used within this product family .

Based on the available information, I can confirm that the Rexroth CD70 is a tie-rod hydraulic cylinder series, and the "R" in CD70R refers to a specific mounting style. However, the exact technical drawing for the specific configuration you requested is not available in these results .📘 Confirmed Series Specifications for CD70The following specifications are confirmed for the CD70 series, which applies to your cylinder with a 25 mm bore .Parameter SpecificationSeries CD70 (Tie-Rod Cylinder) Nominal Pressure 70 bar <7> Piston Diameter (ØAL) 25 mm (range: 25–200 mm) Piston Rod Diameter (ØMM) 12 to 140 mm (a 12 mm or 16 mm rod is common for this piston size) Stroke Length Up to 3000 mm 🔍 How to Find Exact SpecificationsTo obtain the precise dimensions for the "R" mounting style and to confirm if a 200 mm stroke with a 25 mm piston is permissible (to avoid piston rod buckling), it is recommended to consult the official Rexroth datasheet RE 17016/07.03 directly. The datasheet contains detailed dimension tables and permissible stroke length calculations for each mounting type.

Based on the search results, it appears your query for the Rexroth CD 120B cylinder may contain a typo. The model number is likely CDL1, CD210, or another variant from the Rexroth tie-rod or mill-type cylinder families. None of the search results reference a "CD 120" model.I have organized what I could find from the available documentation to provide you with the most relevant information.🔍 Likely Cylinder Series and SpecificationsThe following series and technical data have been identified from Rexroth product documentation:CDL1 Mill Type Cylinders Type: Tie rod or mill typeNominal Pressure: 160 bar (16 MPa)Piston Diameter (ØAL): 25 to 200 mmPiston Rod Diameter (ØMM): 14 to 110 mmKey Weight (40mm Piston):MF3 Mounting: 2.42 kg at 0mm stroke + 0.85 kg per 100mm strokeMT4 Mounting: 3.00 kg at 0mm stroke + 0.85 kg per 100mm stroke⚠️ Important Design ConsiderationWhen selecting a cylinder, you must account for the load on the piston rod. With extreme shock loads, mounting elements and piston rod threads must be specifically designed for durability and endurance strength .

Based on the available information, the Rexroth - Bosch Hydraulic Cylinder Tie Rod Design (Single Rod Cylinder - Series CD 120N) you are looking for does not appear to be listed in the standard product catalogs. The letter "N" in the model number likely designates a specific, possibly non-standard, mounting style for the CD series.To help you find the correct cylinder, here are the specifications for the broader Rexroth CD tie-rod cylinder series, which includes models like CD70, CD210, and CDT3.📊 Standard Rexroth Tie-Rod Cylinder SpecificationsParameter Specification SourceSeries Tie-Rod Cylinder (e.g., CD70, CD210, CDT3) Nominal Pressure 70 ... 210 bar Piston Diameter (ØAL) 25 mm (range: 25...200 mm) Stroke Length (S) 200 mm (max up to 3000 mm) Mounting Types Foot, flange, clevis, trunnion, etc. 🔍 How to Find the Exact "CD 120N" ModelThe "N" likely refers to a specific mounting style, as the CD series offers many mounting options like MP5, MF3, MT4, and MS2. To find the correct specifications:Verify the Mounting Style Code: The letter "N" is not a standard Rexroth code in the documents available. Common mounting style codes include MP5 (self-aligning clevis), MF3 (round flange), and MT4 (trunnion). Confirming the exact mounting type you need is the most important step.Consult Official Documentation: The RE 17016/07.03 document, which you referenced, is the correct primary source for the CD tie-rod cylinder series. A detailed review of this document will provide the complete list of available mounting styles and their dimensional drawings for the 25mm bore size.Contact Rexroth Support: For the most accurate information on a non-standard or custom model variant, contacting Bosch Rexroth directly is the best approach.